PipeFit Plug-in. Design simple or complex pipe joints in 3D inside SheetCAM with this plug-in. Do Copes, Bird mouths, Miter or Flat cutoffs. Intersect two or more pipes of different sizes and at different angles. You can request a Demo for 32 or 64 bit LINUX systems using the DEMO REQUEST tab below. If you have the Demo Installed and working you can order the software here using the buy option. You need the SheetCAM License ID. Once your order is processed you will be sent an email with the PIpefit License File Code to make PipeFit fully licensed.
NOTE : PIPEFIT® is a plug-in for SheetCAM . It ONLY WORKS with the LINUX version of SheetCAM and later versions 6.1.57 or later DO NOT ORDER IT IF YOU ARE RUNNING WINDOWS SHEETCAM ! Once a licnse is issued , NO REFUNDS INSTALL AND RUN THE DEMO BEFORE YOU BUY A LICNESE!
Model, Edit, View, and Contour Generation in one application.
Just type in the parameters such as Header OD, Branch OD, Wall Thickness, Joint Angle, X and Y offsets and Rotation Angle.
The software DRAWS IT FOR YOU and shows you the joints and the cuts in both 3D and 2D. Add as many joints to a Header with different sized pipes and at different angles or rotations and then cut the header or cut each branch as a separate JOB.
Unique PROJECTS method lets you design and save any joint or set of joints then OPEN, EDIT and SAVE a new Project from the results. Setup libraries of common pipe sizes and joints and reload them to build new designs
View any Project in 3D and rotate to see the joints, or in 2D to show you what the PART will look like in SheetCAM. Turn any joint into a PART for SheetCAM to use with the click of a SINGLE BUTTON. Uses familiar SheetCAM Workspace and existing Plasma Toolsets. Fully compatable with DCC and TAPadvanced automated plasma cutting options.
POP-UP Help Windows on each type of joint shows you the names of each parameter.
Supports multiple types of joints like BEVEL, MITER, Y and DEAD END CAP. On Surface or Through Hole .
FREE! * SHEETCAM POSTS for CommandCNC™
Users with DTHCIV/DTHC5 can take advantage of automatic settings for your plasma (DCC) and if you have the Hypertherm RS485 serial option and the HyT-Connect RS485 SIIM Kit you can use full TAP. A good THC is essential to doing rotary cutting due to the variations in pipe roundness and exact size.
Sample Project Files for SheetCAM TNG. Take your choice of using a 5th Axis as either A or B. No swapping over plugs or motors on a plasma table with a rotary axis. Switch back and forth from flat to rotary in seconds, or build a dedicated pipe cutter.
* You can get a trial version of Pipefit
See Rotary Bundle for combo deal with Rotary Plasma Plugin (required)
PipeFit Pro is the first Direct-to-Cut CAM Pipe Joint Design Software. Design -> Toolpath -> G-Code => CUT. Take your simple or complex multi-joint pipe and tubing cuts from idea to actual rotary cut file in minutes. Save and re-use joints. Cut different types of joints. Cut On-Surface or Through Hole. Spend your time CUTTING instead of DRAWING and Hand Cutting Joints.
SOFTWARE STANDALONE LICENSES AND BUNDLES ONLY AVAILABLE WITH Plug-N-Run, Special Bundles or MP3700 Series systems from CandCNC running CommandCNC (LINUX). CandCNC only sells and supports hardware and software to North America, and some parts of Western Europe. We will not provide DEMO or Licensed software outside those areas.
PipeFit Plug-in Standalone Software License
$265.00
PipeFit Plug-in. Design simple or complex pipe joints in 3D inside SheetCAM with this plug-in. Do Copes, Bird mouths, Miter or Flat cutoffs. Intersect two or more pipes of different sizes and at different angles. You can request a Demo for 32 or 64 bit LINUX systems using the DEMO REQUEST tab below. If you have the Demo Installed and working you can order the software here using the buy option. You need the SheetCAM License ID. Once your order is processed you will be sent an email with the PIpefit License File Code to make PipeFit fully licensed.
NOTE : PIPEFIT® is a plug-in for SheetCAM . It ONLY WORKS with the LINUX version of SheetCAM and later versions 6.1.57 or later DO NOT ORDER IT IF YOU ARE RUNNING WINDOWS SHEETCAM ! Once a licnse is issued , NO REFUNDS INSTALL AND RUN THE DEMO BEFORE YOU BUY A LICNESE!
Description
Model, Edit, View, and Contour Generation in one application.
Just type in the parameters such as Header OD, Branch OD, Wall Thickness,
Joint Angle, X and Y offsets and Rotation Angle.
The software DRAWS IT FOR YOU and shows you the joints and the cuts in both 3D and 2D.
Add as many joints to a Header with different sized pipes and at different angles or rotations and then cut the header or cut each branch as a separate JOB.
Unique PROJECTS method lets you design and save any joint or set of joints then OPEN, EDIT and SAVE a new Project from the results. Setup libraries of common pipe sizes and joints and reload them to build new designs
View any Project in 3D and rotate to see the joints, or in 2D to show you what the PART will look like in SheetCAM. Turn any joint into a PART for SheetCAM to use with the click of a SINGLE BUTTON. Uses familiar SheetCAM Workspace and existing Plasma Toolsets. Fully compatable with DCC and TAPadvanced automated plasma cutting options.
Supports multiple types of joints like BEVEL, MITER, Y and DEAD END CAP. On Surface or Through Hole .
FREE! * SHEETCAM POSTS for CommandCNC™
Sample Project Files for SheetCAM TNG. Take your choice of using a 5th Axis as either A or B. No swapping over plugs or motors on a plasma table with a rotary axis. Switch back and forth from flat to rotary in seconds, or build a dedicated pipe cutter.
* You can get a trial version of Pipefit
PipeFit Pro is the first Direct-to-Cut CAM Pipe Joint Design Software. Design -> Toolpath -> G-Code => CUT. Take your simple or complex multi-joint pipe and tubing cuts from idea to actual rotary cut file in minutes. Save and re-use joints. Cut different types of joints. Cut On-Surface or Through Hole. Spend your time CUTTING instead of DRAWING and Hand Cutting Joints.
SOFTWARE STANDALONE LICENSES AND BUNDLES ONLY AVAILABLE WITH Plug-N-Run, Special Bundles or MP3700 Series systems from CandCNC running CommandCNC (LINUX). CandCNC only sells and supports hardware and software to North America, and some parts of Western Europe. We will not provide DEMO or Licensed software outside those areas.
Demo Request