MP3700 – ROUTER Only: + PC preloaded with Linux w/CommandCNC (ROUTER/SPINDLE)
$1,175.00
MP3700-ROUTER ETHER-CUT system Complete front end I/O comes with external cards for tying in Inputs and connecting Table I/O INPUT interface located on rear for up to 15 isolated inputs.Dual Aux Relay mounted in rear panel for control of two AC outputs (1-2H Hand held router, Mist and Flood or other loads to 1200 watts) to individual motor drivers that take Step & Dir logic signals (5V) or the Gecko G540 Via a single ribbon cable (not included) Includes LINUX PC and CommandCNC software Options marked with * must have a selection made or order will not continue. Detailed COMPARISON CHART with Acorn and MASSO: Click here
Same specs as the popular MP3600 but with our new Direct Ethernet EBOB card and the new DTHC 5 5th generation THC. This controller comes with a Linux computer and CommandCNC software.
NOTE: We no longer supply the DB-25 cable to connect the Axis I/O (MTA250 card)
Pre-Configured LINUX PC ( New Mini PC w/2yr warranty) Has CONFIGS for Simple Router and for VFD/Spindle
Installed Drawing (Inkscape), QCAD, and Demo Copy of SheetCAM (use your Windows License)
Universal AC of 100 to 240VAC 50/60 hz No other power suppl;ies needed.
Two 10A 120V AC rated Switched AC outlets fo up to 2HP rated conventional routers.
Cat 5 cables for Ethernet to PC included)
Licensed Copy of CommandCNC™ Control software Nothing else to buy!
Licensed Copy of SheetCAM for 2D and 2.5D routing .
Custom Post Processors for SheetCAM and Vectric to do Automated Router including new Toolchange POSTS forboth
External MTA250 Card provides screw terminals for up to 6 axis of Step & Dir (Driver interface ) Easy wiring to most Stepper and servo DRIVERSs
Built-in 15 input Opto isolated on rear panel for easy access. Plugs for our Ohmic Sensor or the Super Z (plasma) or LPTS (low profile toolsetter
Connects Homes, Limits, Probes, safety switches , tool setter and other NO or NC switches or sensors.
Uses new Direct Ethernet Breakout (EBOB) with expanded Inputs and Outputs
Quad Relay connector to expand relays to 6 (4 more 10A switched relays.)
Options include the RS485 hub that talks to most VFD’s and offers ON/OFF, FWD/REV and 0-10VDC analog Speed control . It will also support the more advanced full RS485 interface on SOME specific VFD’s and provides the new ANTI-STALL torque sensing feature.
THE MP3700 – Router is an advanced Ethernet connected Breakout Board, (EBOB) running o CommandCNC™. It can be used to build simple or sophisticated CNC plasma and/or router tables using steppers or servos as long as the drivers can take discreet step and direction logic signals. THIS IS YOUR BEST CHOICE for a running Plasma or Plasma/router table to continue to use the power supply, motors and mechanics. Not all motor drivers are compatible so check your driver specs first. If your current controller is self contained with proprietary software this WILL NOT plugin and run!
Additional information
Weight
10 lbs
Dimensions
14 × 14 × 14 in
Plasma Connection Kits
Once you have the MP3700-DTHC 5 and its optons selected and in your cart then its important to find the proper THC connection Kit that ties your plasma to the Digital Pickup (PWM Module) that comes with the MP3700-DTHC5
The MP3700-DTHC5 is the perfect solution for Plasma or Plasma-Router tables where the power section (AC and DC power , motor drivers , and motors) already exists or another power solution is desired. It handles all of the magic motion control , software, Torch Height Control and I/O signals. Hook up to 16 totally isolated noise immune filtered inputs for Homes , Limits, Safety Switches, Sensors etc. The MP3700 adds the next generation DIRECT ETHERNET EBOB that can control up to 8 motors. It all connects through the new MTA250 that has 8 step & Dir connection terminals. If your motor drivers can handle TTL level (5 vott) logic signals using “Step” and “Direction” (sometimes called PULSE and CW/CCW ) this system will give you pro level control using our famous CommandCNC running on LINUX. Used to poor performance THC’s or earlier generations of MACH based THC’s? The DTHC 5 will blow you away! With its own high speed independent processor it HELPS you cut by setting all of the cut parameters from the G-Code that is generated using our custom SheetCAM posts (free) . No more pushing buttons, twisting knobs or looking up values. Go hog wild and add the Optional RS485 SIM kit for the Hypertherm RS485 serial port (option from Hypertherm on most Powermax systems) and you then have TAP….Total Automated Plasma.
Ships with Universal 100 to 250 VAC power
Compact 10 X 7 X 3 Instrument case
Rear Panel connection card (Table I/O) with 15 inputs and direct plug for Feather Touch Ohmic Sensor OR Super Z option
Has all external modules (digital pickups) for DTHC 5 including new PWMIIA
Direct cable interface to all Hypertherm Powermax ® plasma cutters and TD “A” series
Connection Kits for other types of plasma available.
Super High Speed DTHC with PID tuning and real time response. Get astounding Z speeds while cutting.
Runs on Open Source (free) LINUX and uses LINUXCNC with CommandCNC™ layer
New AUTO – SET (cut and learn ) for DTHC
Scared of LINUX? Don’t be. It is 100% GUI (even our setup and configuration tools) and it talks to any Windows network, or uses any memory stick . Transfer files and use compatible applications on either platform SheetCAM (unlicensed) comes preloaded on the PC along with drawing and CAD programs. if you have a vlaid license for TNG on Windows it will work on the LINUX PC as well. Process your files on either platform.
MP3700 – ROUTER Only: + PC preloaded with Linux w/CommandCNC (ROUTER/SPINDLE)
$1,175.00
MP3700-ROUTER ETHER-CUT system
Complete front end I/O comes with external cards for tying in Inputs and connecting
Table I/O INPUT interface located on rear for up to 15 isolated inputs.Dual Aux Relay
mounted in rear panel for control of two AC outputs (1-2H Hand held router, Mist and Flood or other loads to 1200 watts)
to individual motor drivers that take Step & Dir logic signals (5V) or the Gecko G540
Via a single ribbon cable (not included) Includes LINUX PC and CommandCNC software
Options marked with * must have a selection made or order will not continue.
Detailed COMPARISON CHART with Acorn and MASSO: Click here
Description
Same specs as the popular MP3600 but with our new Direct Ethernet EBOB card and the new DTHC 5 5th generation THC. This controller comes with a Linux computer and CommandCNC software.
NOTE: We no longer supply the DB-25 cable to connect the Axis I/O (MTA250 card)
VFD’s and provides the new ANTI-STALL torque sensing feature.
Additional information
Plasma Connection Kits
Once you have the MP3700-DTHC 5 and its optons selected and in your cart then its important to find the proper THC connection Kit that ties your plasma to the Digital Pickup (PWM Module) that comes with the MP3700-DTHC5
Here is the link
ink
MP3700 Info tab
The MP3700-DTHC5 is the perfect solution for Plasma or Plasma-Router tables where the power section (AC and DC power , motor drivers , and motors) already exists or another power solution is desired. It handles all of the magic motion control , software, Torch Height Control and I/O signals. Hook up to 16 totally isolated noise immune filtered inputs for Homes , Limits, Safety Switches, Sensors etc. The MP3700 adds the next generation DIRECT ETHERNET EBOB that can control up to 8 motors. It all connects through the new MTA250 that has 8 step & Dir connection terminals. If your motor drivers can handle TTL level (5 vott) logic signals using “Step” and “Direction” (sometimes called PULSE and CW/CCW ) this system will give you pro level control using our famous CommandCNC running on LINUX.
Used to poor performance THC’s or earlier generations of MACH based THC’s? The DTHC 5 will blow you away! With its own high speed independent processor it HELPS you cut by setting all of the cut parameters from the G-Code that is generated using our custom SheetCAM posts (free) . No more pushing buttons, twisting knobs or looking up values. Go hog wild and add the Optional RS485 SIM kit for the Hypertherm RS485 serial port (option from Hypertherm on most Powermax systems) and you then have TAP….Total Automated Plasma.
Scared of LINUX? Don’t be. It is 100% GUI (even our setup and configuration tools) and it talks to any Windows network, or uses any memory stick . Transfer files and use compatible applications on either platform SheetCAM (unlicensed) comes preloaded on the PC along with drawing and CAD programs. if you have a vlaid license for TNG on Windows it will work on the LINUX PC as well. Process your files on either platform.