BladeRunner G5 Legacy Upgrade Replacement Controller Unit (no motors).
$2,650.00$2,550.00
For Upgrade of the main controller box of an existing Bladerunner 620-4 controller box. This is to replace a complete main control box, or to provide a easy plug-n-run upgrade without sending in your old control box for upgrade.
G5 ESPIIA/B Smart Power Control box/ Latest G5 design with new Mini PC Preloaded with CommadnCNC.
4 G251 Gecko Stepper drivers (tested)
All Internal Logic including EBOB, DTHC 5, Table I/O, MTA 250 and Bios supplies are included
Plug and run for existing Bladerunnner controllers, or any system that used the 23 frame 620 oz-in steppers
DOES INCLUDE: RS485 4 port hub, PWMIIA Module,
No Motors. Your existing motors with the flat 4 wide connectors will plug in and run.
Not intended for original builds . THIS IS AN UPGRADE.
Everything you need but the the motors and motor cables .
Carries Full 2 year Warranty on new controller.
Does not include Plasma connection kit or license for SheetCAM .
IF Something BAD happened to your existing Bladerunner 620-4 Control Box and it’s not repairable or too costly, this is a fully operational MAIN G5 control box with power section, drivers, all front end logic and internal cards, assembled and tested. Its a FULL G5 UPGRADE but with the LEGACY older 4 wide motor connectors so you do not have to replace existing motors and rewire the table .
This is designed for the situation where the main control box has suffered electrical damage or physical damage that is not covered by warranty . This new box is an UPGRADE /Replacement that allows you to move from the older Windows /MACH3 based BladeRunner and Windows PC to a NEW G5 control box and NEW quad processor MINI PC preloaded with LINUX and CommandCNC(tm). Instead of sending in you old controller for the UPGRADE, this replaces the whole controller with new everything includigng Power Section , DTHC5, EBOB and Drivers. Carries a full 2 year warranty when used with our 23 frame 620 oz-in steppers .
This not for a new build. It does not include the Plasma Connection kit and it does not have a license for SheetCAM . Its for existing installs of CandCNC controllers using the 23 frame 620 oz-in steppers . It’s not designed for servos or the larger PlazPak controllers with 34 980 motors
Additional information
Weight
55 lbs
Dimensions
22 × 22 × 14 in
What's Included
BladeRunner G5 DTHC V Power Supply Box AIO (White)
Quad Processor Intel based MINI PC w/ Keyboard and Mouse (No Monitor)
PC preloaded with CommandCNC , drawing and CAD proframs
Green CAT5 Ethernet Cable
Yellow CAT5 Ethernet Cable
Blue CAT5 Ethernet Cable
Shielded USB cable (to 4 port hub)
PWMIIA Module
4 Port Hub
2 year (24 Month) Warranty and phone support.
BladeRunner G5 Legacy Upgrade Replacement Controller Unit (no motors).
$2,650.00$2,550.00For Upgrade of the main controller box of an existing Bladerunner 620-4 controller box. This is to replace a complete main control box, or to provide a easy plug-n-run upgrade without sending in your old control box for upgrade.
Carries Full 2 year Warranty on new controller.
Does not include Plasma connection kit or license for SheetCAM .
Description
IF Something BAD happened to your existing Bladerunner 620-4 Control Box and it’s not repairable or too costly, this is a fully operational MAIN G5 control box with power section, drivers, all front end logic and internal cards, assembled and tested. Its a FULL G5 UPGRADE but with the LEGACY older 4 wide motor connectors so you do not have to replace existing motors and rewire the table .
This is designed for the situation where the main control box has suffered electrical damage or physical damage that is not covered by warranty . This new box is an UPGRADE /Replacement that allows you to move from the older Windows /MACH3 based BladeRunner and Windows PC to a NEW G5 control box and NEW quad processor MINI PC preloaded with LINUX and CommandCNC(tm). Instead of sending in you old controller for the UPGRADE, this replaces the whole controller with new everything includigng Power Section , DTHC5, EBOB and Drivers. Carries a full 2 year warranty when used with our 23 frame 620 oz-in steppers .
This not for a new build. It does not include the Plasma Connection kit and it does not have a license for SheetCAM . Its for existing installs of CandCNC controllers using the 23 frame 620 oz-in steppers . It’s not designed for servos or the larger PlazPak controllers with 34 980 motors
Additional information
BladeRunner G5 DTHC V Power Supply Box AIO (White)
Quad Processor Intel based MINI PC w/ Keyboard and Mouse (No Monitor)
PC preloaded with CommandCNC , drawing and CAD proframs
Green CAT5 Ethernet Cable
Yellow CAT5 Ethernet Cable
Blue CAT5 Ethernet Cable
Shielded USB cable (to 4 port hub)
PWMIIA Module
4 Port Hub
2 year (24 Month) Warranty and phone support.