BladeRunner G5/G5A Replacement Controller (only) Unit.
$2,760.00
For replacement of the main controller box of an existing G5 or G5A controller box. This is to replace a badly damaged main control box or to provide a quick repair of a system that has working external modules.
ESPIIA/B Smart Power Control box
4 G251 Gecko Stepper drivers (tested)
All Internal Logic including EBOB, DTHC 5, Table I/O, MTA 250 and Bios supplies are included
Plug and run for existing G5 or G5A controllers
DOES NOT INCLUDE: RS485 4 port hub, PWMIIA Module,
NO External cables, NO PC, No Software .
Not intended for original builds . THIS IS NOT AN UPGRADE
IF Something BAD happened to your existing G5 or G5A control Box and it’s not repairable or too costly this is a fully operational MAIN ESPIIA/B control box with power section, drivers, all front end logic and internal cards, assembled and tested.
This is designed for the situation where the main control box has suffered damage from a flood or electrical storm or physical damage that is not covered by warranty . You must have all of the external modules, cables and correct motors / connectors. Designed to unplug the (working) PC and external modules and plug them in and get back running quickly.
Do not buy this to try and fix or upgrade an older BladeRunner system, it won’t WORK! NO REFUNDS. Warranty limited to 12 months.
Additional information
Weight
55 lbs
Dimensions
22 × 22 × 14 in
What's Included
BladeRunner G5 DTHC V Power Supply Box AIO (White)
(4) 620 Stepper Motors Prewired with 4 pin round connectors
Recovery Memeory Stick (Computer)
Green CAT5 Ethernet Cable
Yellow CAT5 Ethernet Cable
Blue CAT5 Ethernet Cable
Shielded USB cable (to 4 port hub)
PWMIIA Module
4 Port Hub
2 year (24 Month) Warranty and phone support.
G5 Bladerunner Details
Inside look: Modular Design
Then there is the outside!
Top End Exhaust fan
Unique Dual. Driver Modules
Swap out modules in minutes. Upgrade and add 2 more axis….in minutes 4 screws, 2 cables….done
BladeRunner G5/G5A Replacement Controller (only) Unit.
$2,760.00
For replacement of the main controller box of an existing G5 or G5A controller box. This is to replace a badly damaged main control box or to provide a quick repair of a system that has working external modules.
Description
IF Something BAD happened to your existing G5 or G5A control Box and it’s not repairable or too costly this is a fully operational MAIN ESPIIA/B control box with power section, drivers, all front end logic and internal cards, assembled and tested.
This is designed for the situation where the main control box has suffered damage from a flood or electrical storm or physical damage that is not covered by warranty . You must have all of the external modules, cables and correct motors / connectors. Designed to unplug the (working) PC and external modules and plug them in and get back running quickly.
Do not buy this to try and fix or upgrade an older BladeRunner system, it won’t WORK! NO REFUNDS. Warranty limited to 12 months.
Additional information
BladeRunner G5 DTHC V Power Supply Box AIO (White)
(4) 620 Stepper Motors Prewired with 4 pin round connectors
Recovery Memeory Stick (Computer)
Green CAT5 Ethernet Cable
Yellow CAT5 Ethernet Cable
Blue CAT5 Ethernet Cable
Shielded USB cable (to 4 port hub)
PWMIIA Module
4 Port Hub
2 year (24 Month) Warranty and phone support.
G5 Bladerunner Details
Inside look: Modular Design
Then there is the outside!
Top End Exhaust fan
Unique Dual. Driver Modules
Swap out modules in minutes. Upgrade and add 2 more axis….in minutes 4 screws, 2 cables….done