FEATURE LIST

• Modular design is compact and clean
• 11.75"W X 12.5"L X 4 1/5"D Design fits standard 3U rack cases and commercial NEMA case.
• Easy to setup.  All Power connections are .250 Crimp-on connectors
• Unique stacked power design gives choices of output voltages.
• PWM  dynamic braking discharges caps in < 2 sec
• DC output is loaded on any shutdown to brake the motors
• AC Side 20A latching relay is failsafe.  Any failure results in shutdown.
• Quad AC shutdown protection (Main Switch, Panel Breaker, AC Contactor and Electronic softstart)
• New processor based watchdog/control shuts down Motor Power instantly for ANY fault condition
• Supply constantly monitors Motor volts, Motor Current, Case (internal Temperature).
• Ultra Soft Start AC circuit holds inrush current to levels EQUAL TO NORMAL LOAD CONDITIONS!
• Electronic Fusing acts 300 times faster than conventional fuses.
• Any shutdown sequence instantly turns power off to motors and applies dynamic braking
• When used with EZPlug Servo Interface Cards any drive fault shuts down the system
• Overvoltage protection (OVP) keeps line surges or back EMF from motors from damaging drives or components.  Instant shutdown on OVP events.
• 40,000 MFD of filter caps.
• Separate POWER and POWER GROUND for each motor module
• Designed to provide Floating Power to Gecko's (isolated from logic or PC grounds) for increased noise immunity and elimination of ground loop problems.  Gecko mounting plate/heatsink is NOT grounded to chassis. 
• Operation on 110 (120V AC) or 220 (240VAC) single phase (US with neutral line only)
• 220-240VAC 50HZ version available
• Provisions for quick connect of panel power components  such as main power switch, primary side breaker, power cord.
• When used with CandCNC MP1000 products the RUN and STOP (power control) can also be accessed via the MP1000 front panel RUN and STOP buttons and LED's
• NEW!  ESP version adds faster response electronics and full RS232 Multi-drop communications with MACH3!
• Plugins for DB25 cable from most port interface cards (eg Mini-IO, etc)
• Direct interface plug for all CandCNC MP1000 products (via MTA 100 card)
• Sub panel allows easy mounting in a metal or fiberglass case
• Plug compatable with our low cost Mini-IO solutions
• Support for 5 axis or 5.5 axis (6 motors, 1 slaved) operation when used with MP1000C series products. 

With the addition of the EZPLUG Servo or Stepper interface cards the interconnects inside the box have dropped to vitually nothing.  The Geckos snap onto the end connectors on one side and posi-loc motor connectors are on the other.  The Gecko "shelf" has been modified so that the Interface cards fit and will slide up to the end of the NEMA case and provide easy external access to both the motor and (in the case of servos) the encoder runs

Pictured above is the new EZPlug Dual Gecko  Interface card for Servo applications.  It features power-on Reset  for both Gecko's, central fault detection (any fault on any drive shuts down power and issues an e-stop signal) and best of all it has Differential inputs using standard RJ45 for UTP network cables.  The connection is so easy anyone can do it.  One ribbon cable down to the PSC650 card and two sets of power cables down to connectors on the PSC650.  Hookup takes 5 minutes or less!  The cards include 2 Differential driver cards for the servo motors.  Instablility from encoder noise goes AWAY!   $68.00 for a Dual Card and two matching Differential drivers (for USDigital encoders with the 5 pin latching connector)

Pictured above the EZPug Dual GeckoI Stepper Interface allows you to quickly mount one or two Gecko stepper drives.  Gecko current is set with handy Dip Switches.  Drive connectors are 5 wide to prevent plugging them into a servo card. $38.00 for a Dual Card The Interface Cards (servo or stepper) can be stacked top and bottom using our Gecko Mounting plates.  You can run two servos and two steppers or 3 or 4 steppers or servos. NOTE:  For larger servos more than two are not supported.  See the PSC1500 unit for 3 or 4 servo operation