OPTIONS & EXPANSION CARDS Be sure you also order your Plasma Connection Kit from the proper section. These options are for extras not needed on all purchases
Motor Cable Length UpGrade per motor. (select number you want)	On longer tables you may need more cable length on your motors. Add 5 ft sections to as many motors as you want. Example: to extend one motor by 10ft buy two sections and in the Order Notes (on the order sheet) tell us how to apply the sections (one motor X 10ft). For more motors, buy more sections and list how long you want each motor.	QTY: 4.75 per 5' section
INTERNATIONAL POWER OPTION For operation on non-US power Specify 220VAC 50/60HZ configuration if needed .	220-240 VAC 50/60HZ Option. Please add this if you need to run on the higher voltage. All units are shipped for 120VAC 50/60HZ unless this option is added. If you are ordering a Plazpak unit (any size) then there is an added charge for the International Power upgrade (220 - 240VAC 50/60hz)	Plazpak INTERNATIONAL POWER UPGRADE OPTION $35.00

OPTIONS FOR PLASMA
CANDCNC EXCLUSIVE!	DIGITAL CURRENT PROBE DCP-01 Now you can see the actual DC Amps AT THE CUT using our exclusive DCP Add-on module for the DTHC. It is accurate within better than 2% across a range of 20 to 125A (higher range version available on request). Displayed in real time on the same screen as the TORCH VOLTS, it gives you precise information about your plasma cut. No longer do you have to guess at what the true cut current is. Use the Cut Profile to preset fault points so you can prevent bad cuts due to improper dial settings or poor workclamp connections. The DCP also acts as an adjustable ARC OK sensor and it works with any plasma cutter. Each Cut Profile can have it's own ACR OK trip value in AMPS. NOTE You need to order this option if your Plasma cuttier DOES NOT HAVE AN ARC OK (aka Transfer, Arc Xfr, OK to Move) signal.Plugs directly into the new THCSensor-PWM Module	$85.00 :
THC SENSOR PWM Module (Part of the DTHC II System)	The THC Sensor PWM Module mounts on the outside of the plasma cabinet and sends back digital (PWM) signals from Divided Arc Volts. THE MODULE COMES WITH ALL DTHC II based systems. It is listed here as a spare or as a way to add on to a secondary plasma unit. YOU DO NOT NEED TO ORDER THIS PART UNLESS YOU NEED A SPARE, A SECOND INTERFACE FOR ANOTHER PLASMA, OR SOMEBODY STOLE YOUR PLAMSA WITH THE MODULE ON IT!!	$86.50 QTY:
SPARE DRIVES for Plazpaks
G201X Motor Drives Spare Drives	Gecko G201X 7A MicroStepping motor drive. . Combined with any of our PlazPak Stepper Driver units (Plazpak 1 series) and our unique second generation EZPlug II Interface cards the G201X drive becomes almost indestructable. No more drive failures from shorted motor wires or miswired motors. The Smart Power section of all the Plazpak series protects the drives from overvoltage, overload, over-temp and shut down spikes.. We warranty any Gecko used with our ESPII Smart Power Controllers for a full 2 years. Indivdual drives are sold for expansion of Plazpak with the new ESP II and EZPLug II technology (shipped after 12/1/2010. Earlier units used the Gecko G203 drive below. DO NOT REPLACE A G203 in our products with a G201X.	G201X Stepper Drives $99.00 QTY:
	Gecko G320X 20A Brushed DC Servo Motor Drive. . The G320X is the next generation of Closed Loop Servo Drives from Gecko. Used in all our Plazpak 3, 4 and 5 seriers servo systems, It Improves on the features of the older G320 drive and adds in the Step Multiplier Option from the older G340. Combined with our EZPLug Servo Interface card that features true Differntial (noise immune) encoder driver/receiver and our Smart Control that monitors the individual drive fault signals the G320X drive provides a cost effective and reliable solution for brushed DC servo motors	G302X Servo Motor Driver $99.00 QTY:
QUAD RELAY CARD	Quad Relay Card adds 4 more external relays: Two high current and two 1A low current. DB9 input jack. Plugs directly into Table I/O to give a total of 6 relays (4 high current) . This is a raw card assembled and tested. No case provided. With manual.	$48.00 :
MACH3 License	MACH3 Full license (if purchased with any BladeRunner package above) SEE ALSO SOFTWARE BUNDLES	$165.00