HyT-CONNECT®

 INTERFACE CARDS  for  HYPERTHERM Plasma Cutters.
Shop for and buy options for your  CandCNC DTHCII based BladeRunner AIO Dragon-Cut,
MP3000-DTHCII or Plazpak Series products. 
IF YOU DO NOT SEE THE MODEL NUMBER OF YOUR HYPERTHERM
it probably needs the HyT-Connect-RETRO1 kit (first selection) 
If you don't have a Hypertherm plasma cutter,
THEN YOU ARE ON THE WRONG PAGE!!

   

       

 

Connection Kits for

  • HYPERTHERM MODEL 600

  • HYPERTHERM MODEL 900

  • HYPERTHERM MODEL MAX100

  • Most other Hypertherms not listed below

The HyT-Connect - RETRO1 interface kit for the listed Hypertherm models consists of:

RAV-01 Voltage Divider Card (mounts internally)
Cable from RAV-01 to THC Sensor PWM Module (part of DTHCII)
DCP-01 Digital Current Probe (0-100A current sensor & ARC OK sensor)

 

$132.00

QTY:    

Connection Kits for

  • HYPERTHERM MODEL 1000

  • HYPERTHERM MODEL 1250

  • HYPERTHERM MODEL 1650


The HyT-Connect - 1000 interface kit for the listed Hypertherm models consists of:

RAV-01 Voltage Divider Card (mounts internally)

MIC-02 4 conductor Rear CPC connector cable

$92.00

QTY:   

 

Connection Kits for

  • HYPERTHERM MODEL 45

  • HYPERTHERM MODEL 65

  • HYPERTHERM MODEL 85.

  • HYPERTHERM MODEL 105


HyT-Connect Basic Interface Kits 45-105
consists of

  • MIC-01 3ft Custom cable for direct connecton to rear CPC connector.

NOTE:  Model 45 comes stock with rear CPC connector and internal 50:1 divider.  Models 65,85 & 105 have to be ordered (or a reto fit CPC kit ) with the unit.    if you already have a 65 or 85 WITHOUT THE CPC connectior then contact your local dealer and order Hypertherm Kit Part# 223036.  Download the FSB here: 

https://www.hypertherm.com/Xnet/library/library.jsp?file=HYP103983

 

$48.00

QTY:   

Advanced Connection Kits for

  • HYPERTHERM MODEL 65
  • HYPERTHERM MODEL85
  • HYPERTHERM MODEL 105
  • Super Pak: Everything you need to take advantage of all the features the new HyT-Connect interface provides.

    Individual components of this kit are availalble below for separate purchase

    NOTE:  REQUIRES the RS485 Serial Interface (part #228539) be installed in your 65 /85/105.  If your unit does not have the RS485 connector contact your Hypertherm dealer and order the kit .  Download the following FSB:
    https://www.hypertherm.com/Xnet/library/library.jsp?file=HYP109750

Consists of:

  • HyT-Connect RS485 SIM Kit
    Software License
  • C3Bus USB-RS485 4 Port Hub
  • MIC-01 Cable
  • DCP01 Digital Current Probe,
  • New FeatherTouch Ohmic Sensor
  • All cables and software drivers for the DTHCII and MACH3
  • New DCC Dynamic Cut Feature

Consists of:

  • HyT-Connect RS485 SIM Kit B,  
  • MIC-01 Cable, NG
  • DCP01 Digital Current Probe,
  • New FeatherTouch Ohmic Sensor
  • all cables and software drivers for the DTHCII and MACH3
  • New DCC Dynamic Cut Features

     

$435.00

QTY:    

 

 

 

$367.00
Kit B (less C3Bus 4 port Hub)

QTY:    

OPTIONS FOR PLASMA & DTHC II 
NOTE:  The HyT-CONNECT Kits above may have one or more of these options included.  Read the descriptions before you order. 

WARNING!  Do NOT try to use the FT-01 without a backup system to stop motion in case the ohmic touch does not work!  The ohmic sensor will fail on dirty, rusty or coated material.  The typical Z axis with leadscrew has enough force to damage or break the end of you torch   You need the Floating Holder to act as a shock absorber and its touch switch to use as a backup.. 

 FT-01 FeatherTouch Ohmic Sensor

Makes your torch Tip a highly sensitive touch sensor by sensing when the tip touchs a piece of metal on the table.  Virtually zero downforce is appled so it is perfect for cutting thin materials.  It will not push down bowed or warped material during the touch-off sequence so there is no "spring back" error like there can be using the Floating Torch Holder alone.  The FT=01K Kit comes complete with 25 ft stranded wire cable** connected at the sensor end that connects it to a small snap on adapter for the CandCNC Table I/O.  Hookup and setup should take just a few minutes. Works with all BaldeRunner, MP3000-DTHC, PlazPaks.  Comes with
  • FT-01 Ohmic Sensor Module
  • 9 to 14VDC Wallplug transformer (120VAC only)
  • 25 ft multiconductor stranded cable, connected at the sensor end and tested,
  • Connection wires for the Torch tip and table common and to connect the prior Touch Swtich to the sensor as a limit
  • Table I/O interface card (mounted on the table I/O card)
  • Illustrated manual with MACH setup suggestions 

    • FT-01K Feather Touch Ohmic Sensor Kit


    $72.00

    IIncluded in Advanced Connection Kits above

    CANDCNC EXCLUSIVE!
    "sniffs" the current at the cut!

    DIGITAL CURRENT PROBE DCP-01
    Now you can see the actual DC Amps AT THE CUT using our exclusive DCP add-on module for the DTHC.  It is accurate within better than 2% across a range of 20 to 125A (higher range version available on request).  Displayed in real time on the same screen as the TORCH VOLTS,  it gives you precise information about your plasma cut.  No longer do you have to guess at what the true cut current is.   Use the Cut Profile to preset fault points so you can prevent bad cuts due to improper dial settings or poor workclamp connections.  The DCP also acts as an adjustable ARC OK sensor and it works with any plasma cutter.  Each Cut Profile can have its own ACR OK trip value in AMPS. 

    NOTE: You need to order this option if your Plasma cutter DOES NOT HAVE AN ARC OK (aka Transfer, Arc Xfr, OK to Move signal.) It Plugs directly into the new THCSensor-PWM Module

        DCP-01 

             $94.50

    :

    Works with all plasma cutters

    Included in Advanced Connection Kits above

     

    HyT-CONNECT® RS485 SIM KIT.  Allows remote control of Current and Air pressure Settings on models 65, 85 and 105 Hypertherm Cutters.  Values are set automatically from the MACH3 control software.

    Requires Hypertherm Optional RS485 Port on your plasma cutter.  It can be added in the field.  Contact your Hypertherm reseller to order.


     



    HyT-Connect RS485 SIM Kit A
    Consists of:

    • 4 PORT USB to RS485 PC interface Module C3BUS HUB ®**
    • RJ45 Cat5E UTP cable 25ft
    • 5V Wallplug power source
    • RJ45 to 5 pin RS485 plug adapter card
    • Windows USB drivers for the module
    • Custom MACH3 communications driver
    • Custom operator screens and expanded CUT PROFILE
    • Instruction Manual (CD)
    • Auto installer for software and drivers

    • HyT-Connect RS485 SIM Kit B
      Consists of
    • Same as above except no 4 Port USB to RS485 C3Bus Hub
    • For systems that already have a C3Bus Hub.

      ** NOTE: IF you already have one of the USB-RS485 4 PORT c3Bus HUBS that is shipped with other CandCNC equipment you need to order the HyT-Connect RS485 SIM Kit  Less HUB listed below.  You only need one 4 port hub per system.

        
    HyT-Connect RS485 KIT A
    $249.00

    QTY:

    Exclusively for the Hypertherm 65, 85  and 105 with an installed RS485 Serial OPTION

     

     

     HyT-Connect RS485 KIT B (No Hub)

    $190.00

    QTY:


    Order this if you already have a C3Bus 4 port USB to RS485 Hub