OPTIONS & EXPANSION CARDS PART II

Shop for and buy options for your BladeRunner AIO, BladeRunner AIO Dragon-Cut or Plazpak. Options are by section. Not all options work with all models of controllers.

Motor Cable Length UpGrade per motor. (select number you want)

On longer tables you may need more cable length on your motors. Add more 5 ft sections to as many motors as you want. Example: to extend one motor by 10ft buy two sections and in the order Notes tell us how to apply the sections (one motor X 10ft). For more motors, buy more sections and list how long you want each motor.

Specify 220VAC 50/60HZ configuration if needed

FREE for BLADERUNNER's ONLY Order for Plazpaks using the PLAZPAK Button
.

220VAC 50/60 Option. Please add this no cost option if you need your BladeRunner to run on the higher voltage. All units are shipped for 120VAC 50/60HZ unless this option is added. If you are ordering a Plazpak unit (any size) then there is an added charge for the International Power upgrade (220 - 240VAC 50/60hz)

BladeRunner
Free

Plazpak $35.00

OPTIONS FOR PLASMA & DTHC II
Note: Some of these options are included in the Connection Kits for your plasma cutter. Go to the Plasma Connection Kits page first.

CANDCNC EXCLUSIVE!
"sniffs" the current at the cut!

DIGITAL CURRENT PROBE DCP-01
Now you can see the actual DC Amps AT THE CUT using our exclusive DCP Add-on module for the DTHC. It is accurate within better than 2% across a range of 20 to 125A (higher range version available on request). Displayed in real time on the same screen as the TORCH VOLTS, it gives you precise information about your plasma cut. No longer do you have to guess at what the true cut current is. Use the Cut Profile to preset fault points so you can prevent bad cuts due to improper dial settings or poor workclamp connections. The DCP also acts as an adjustable ARC OK sensor and it works with any plasma cutter. Each Cut Profile can have it's own ACR OK trip value in AMPS. NOTE You need to order this option if your Plasma cuttier DOES NOT HAVE AN ARC OK (aka Transfer, Arc Xfr, OK to Move) signal.Plugs directly into the new THCSensor-PWM Module

DCP-01

$85.00

6ft Custom interface cable. For DTHC II systems Only Order MIC-01 or MIC02 based on the model and features of your HYPERTHERM or THERMALDYNAMICS plasma cutter. This cable will not work with other plasma cutters or other models that do not have the rear panel CPC connector. It will not work with any other THC or DTHC but the DTHCII and the THC Sensor PWM Module

MIC CUSTOM MACHINE INTERFACE CABLE 6ft
One end plugs to the Rear CPC connector on your Plasma the other into the THC SENSOR PWM Module
Read this carefully!
The new Hypertherm 45/65/85 series plasma cutters and the new Thermal Dynamics A60/A80/A120 can be ordered with a rear panel Automation Connector (CPC Recepticle) that allows direct access to some or all of the signals needed for CNC automation.

IF YOU HAVE THIS CONNECTOR:

THE MIC-01 is for plasma units that have the internal voltage divider option and the divided volt appears on the rear CPC.

THE MIC-02 is for plasma units that DO NOT have the internal voltage divider option but have the rear CPC for the START (TORCH ON) and ARC OK (Transfer) signals See the RAV-01 Card below for a voltage divider card (universal).

Note: Some TD 52/82/102 units can be ordered with the CPC rear connector. The Automation Interface Card for divided volts is optional and must be purchased from TD separately.

MIC-01

$45.00

MIC-02
$41.00

Order this card if you do not have an internal voltage divider card or one that is not compatable with the Inputs of the THC Sensor PWM Module

RAV-01 Raw Arc Volts Voltage Divider Card.

Designed for plasma units that do not have an integrated ARC Volts divider (most units do not), this card mounts inside the plasma unit and is connected to the Electrode leads and the Workclamp leads inside (raw arc volts).. It also has screw terminals to use for the TORCH swtich and to pick up an ARC OK signal IF YOUR UNIT has one. The card has test buttons to confirm connections. Manual covers how to find and interface to most plasma cutters. If you have an older Hypertherm (1000, 1250, 1650) or TD with no voltage divider option (but with internal ARC OK and START signals) then you should order this card with your DTHCII. If your plasma is not setup for automation then you need this card and probabaly the DCP-01 to get an arc ok. Raw voltage is divided, filtered and is directly connected through a sheilded cable (supplied) to our THC Sensor PWM module. 4 wide connector for other signals also included. Works with both hand torch and machine torch setups.

RAV-01
$41.50

OTHER OPTIONS: Things you might like to have.

PN200 48 Function HAND CONTROLLER

With the PN200 you can control vitrually all of the setup and running functions for a CNC plasma or router. This is NOT a keyboard emulator. All functions are directly sent to MACH. The jog can be done with either the 360 deg multi-axis jogstick or from the individual axis jog buttons on the keypad. You also have the ability to change DTHC settings (while cutting) and to do feedrate override. Start stop and pause the cut program. The Using a CandCNC designed USB to RS485 adapter module the PN200 is designed to work in a high noise environment and uses industrial communication standards (RS485) to allow long cable runs up to 50ft from the control PC. Our exclusive "BIG SCREEN" feature pops up an oversized screen on your monitor when there are settings are changing that you need to see. Couple that with the ability to run up to 90 custom MACROS and you have a light. compact true Hand control. Safety featues include a hardwired E-STOP back to our controls and instant E-STOP if it gets unplugged.

For our interacive Features and Help file click the photo.

Includes:PN200 USB to RS485 module, 25ft cable, Install CD, CD manual. 2 year warranty.

$215.00
(when purchased with any Plug-n-Run system)

QUAD RELAY CARD

Quad Relay Card adds 4 more external relays: Two high current and two 1A low current. DB9 input jack. Plugs directly into Table I/O to give a total of 6 relays (4 high current) . This is a raw card assembled and tested. No case provided. With manual.

NOTE all Plug-n-Run systems ship with 2 auxillart relays on the TABLE I/O card. This option adds 4 MORE realsy to that. On Plasma models (with the DTHC or DTHC II) there is an added relay to fire the torch (3 relays are stock)

$48.00

MACH3 License

MACH3 Full license (if purchased with any BladeRunner package above)

SEE ALSO SOFTWARE BUNDLES

$165.00

G251-SOLO KIT

Add the missing 5th driver for building a rotary axis .

Upgrade option on BladeRunner4Combo and BladeRunner Dragon Cut (plasma). Standard on Super MAX5

NOT FOR PLAZPAK SYSTEMS

Kit is installed and tested in MAX5 and Dragon-Cut 620-5. Can be added in the field in minutes

Get ready for the next big plasma cutting technology that will drive down the cost of Rotary cutting! The 5th axis upgrade for the BladeRunner AIO adds a full G251 motor driver with isolated inputs and the same protections as the drives on the main EZPlug G251-4 module at an affordable price. You also get a special Rotary Wizard for pipe and tubing cutting that makes rotary plasma cutting a lot easier. Free SheetCAM POST for round AND Rectangular tubing

The KIT allows you to tap into the AXIS I/O cable from the UBOB to the G251-4 module and pull out the 5th axis step & dir. Power and logic signals travel on a 10 pin ribbon cable to the G251-SOLO card. All BladeRunner AIO's are shipped 5th axis "ready". 4 screws and some cable connections are all that is needed. Open the BladeRunner AIO case and the 5th axis is installed on the top without removing any sub-assemblies or modules .

G251-SOLO-KIT Kit
$95.00

Upgrade Price w/300 oz-in motor (wired)$143.00

Upgrade Price w/620 oz-in motor (wired)$175.00